大倾角输送带维护和操作说明！
Maintenance and operation instructions for high angle conveyor belts!
在运输和储存过程中，运输胶带应保持清洁，防止日晒或雨雪暴晒，避免与酸、碱、原料油、溶剂等化学物质接触，并保持一米距离。热设备。
During transportation and storage, the transportation tape should be kept clean to prevent exposure to sunlight or rain and snow, avoid contact with chemicals such as acids, alkalis, raw materials, solvents, etc., and maintain a distance of one meter. Thermal equipment.
2、储存过程中，库房温度保持在18-40℃中间，空气湿度保持在50-80%中间。
2. During the storage process, the warehouse temperature is maintained between 18-40 ℃ and the air humidity is maintained between 50-80%.
3. 储存期间，产品必须成卷放置，不能折叠堆放。在储存期间，它们应该每季度滚动一次。
During storage, products must be placed in rolls and cannot be folded or stacked. During storage, they should be rolled quarterly.
4、不同类型、规格、型号的大倾角输送带叠层不宜一起应用，其接头最好采用胶接法。
4. The stacking of high angle conveyor belts of different types, specifications, and models should not be applied together. It is best to use adhesive bonding method for their joints.
5、大倾角输送带的种类、结构、规格和层数应按应用标准有效采用。
5. The types, structures, specifications, and layers of high angle conveyor belts should be effectively adopted according to application standards.
6、大倾角输送带的运行速度一般不宜超过2.5m/s，大块、高磨损的原料和采用固定梨的卸料设备应尽量使用低速齿轮。
6. The operating speed of high angle conveyor belts should generally not exceed 2.5m/s, and low-speed gears should be used as much as possible for large, high wear raw materials and unloading equipment using fixed pears.
7、运输机传动托辊直径与大倾角输送带布层的关系、传动托辊与转向托辊的配套设施及缓冲托辊槽角的规定应有效选择根据运输机的设计要求。
7. The relationship between the diameter of the transmission roller and the fabric layer of the high angle conveyor belt, the matching facilities between the transmission roller and the turning roller, and the regulations on the groove angle of the buffer roller should be effectively selected according to the design requirements of the conveyor.
8、送料方向应与胶带运行方向一致。为减少原料对胶带的冲击，应采用溜槽，减少原料下落距离；在胶带的接收段应减小缓冲辊之间的间隙，并应选择缓冲辊作为溢料。 , 皮带上装有柔软合适的挡板，防止挡板坚固而刮伤大倾角输送带的尼龙大倾角输送带表面。
8. The feeding direction should be consistent with the running direction of the tape. To reduce the impact of raw materials on the tape, chutes should be used to reduce the distance of raw material falling; The gap between the buffer rollers should be reduced in the receiving section of the tape, and the buffer roller should be selected as the overflow material, The belt is equipped with a soft and suitable baffle to prevent the baffle from being strong and scratching the surface of the nylon high angle conveyor belt.
9、大倾角输送带在使用中应注意以下事项：
9. The following precautions should be taken when using high angle conveyor belts:
①防止缓冲托辊被原料覆盖，导致转动不灵敏，避免多余的材料卡在滚筒和胶带之间，注意部分主题活动的润滑，但不要给输送胶带上油；
① Prevent the buffer roller from being covered by raw materials, which may cause insensitive rotation, avoid excess materials getting stuck between the roller and the tape, pay attention to the lubrication of some themed activities, but do not oil the conveyor tape;
②防止带载启动；
② Prevent startup with load;
③胶带产生方向运行如有偏差，使用时采取一定有效措施纠正；
③ If there is any deviation in the direction of the adhesive tape during operation, effective measures should be taken to correct it during use;
④使用人造丝面料时发现胶带有部分破损，进行修复以防膨胀；大倾角输送带生产厂家整理发布！
④ When using artificial silk fabric, it was found that the tape was partially damaged, and repair was carried out to prevent expansion; Large angle conveyor belt manufacturers organize and release!
