产品中心
联系我们
名称：河北博傲橡胶制品有限公司
电话：15081233333
联系人：罗经理
地址：河北省保定市博野县橡胶工业园
新闻动态
输送带接头方法
输送带接头方法：
Conveyor belt joint method:
所有的输送带必须接成环形才能使用，所以输送带接头的好坏直接影响输送带的使用寿命和输送线能否平稳顺畅地运行。 一般输送带接头常用方法有机械接头、冷粘接接头、热硫化接头等。
All conveyor belts must be connected into a ring to use, so the quality of the conveyor belt joint directly affects the service life of the conveyor belt and whether the conveyor line can run smoothly and smoothly. The common methods of conveyor belt joints are mechanical joints, cold bonded joints, hot vulcanized joints, etc.
尼龙输送带保养与维护
Maintenance and Maintenance of Nylon Conveyor Belt
1、输送胶带在运输和贮存中，应保持清洁避免阳光直射或雨雪浸淋,防止与酸、碱、油类、有 机溶剂等物质接触，并距离发热装置一米以外。
1. In transportation and storage, conveyor belts should be kept clean to avoid direct sunlight or rain and snow leaching, to prevent contact with acids, alkalis, oils, organic solvents and other substances, and one meter away from the heating device.
2、贮存时仓库温度宜保持一 18-40 ℃之间，相对湿度宜保持在 50- 80 %之间。
2. Warehouse temperature and relative humidity should be kept between 18-40 C and 50-80% during storage.
3 、贮存期间，产品须成卷放置，不得折迭，放置期间应每季翻动 一次。
3. During storage, the products should be placed in rolls and not folded. During storage, the products should be flipped once a quarter.
4 、不同类型、规格层数的输送带不宜接在一起使用，其接头最好采用胶接法。
4. Conveyor belts of different types and layers of specifications are not suitable to be joined together. It is better to use gluing method for their joints.
5 、输送胶带的类型、结构、规格、层数应根据使用条件合理选用。
5. The type, structure, specifications and layers of conveying belt should be selected reasonably according to the use conditions.
6 、输送胶带运行速度一般不宜大于 2 ． 5 米/秒，块度大，磨损性大的物料和使用固定梨的 卸料装置应尽量采用低速。
6. Conveyor Belt should not run faster than 2.5 m/s. Materials with large fragmentation and abrasion and unloading device of fixed pear should be used as low as possible.
7 、运输机的传动滚筒直径与输送带布层的关系、传动滚筒、改向滚筒的配套以及对 托辊槽角 的要求应根据运输机的设计规定，合理选取。
7. The relationship between the diameter of the driving drum and the layers of the conveyor belt, the matching of the driving drum and the reversing drum, and the requirement of the groove angle of the idler should be reasonably selected according to the design regulations of the conveyor.
Conveyor belt joint method:
所有的输送带必须接成环形才能使用，所以输送带接头的好坏直接影响输送带的使用寿命和输送线能否平稳顺畅地运行。 一般输送带接头常用方法有机械接头、冷粘接接头、热硫化接头等。
All conveyor belts must be connected into a ring to use, so the quality of the conveyor belt joint directly affects the service life of the conveyor belt and whether the conveyor line can run smoothly and smoothly. The common methods of conveyor belt joints are mechanical joints, cold bonded joints, hot vulcanized joints, etc.
尼龙输送带保养与维护
Maintenance and Maintenance of Nylon Conveyor Belt
1、输送胶带在运输和贮存中，应保持清洁避免阳光直射或雨雪浸淋,防止与酸、碱、油类、有 机溶剂等物质接触，并距离发热装置一米以外。
1. In transportation and storage, conveyor belts should be kept clean to avoid direct sunlight or rain and snow leaching, to prevent contact with acids, alkalis, oils, organic solvents and other substances, and one meter away from the heating device.
2、贮存时仓库温度宜保持一 18-40 ℃之间，相对湿度宜保持在 50- 80 %之间。
2. Warehouse temperature and relative humidity should be kept between 18-40 C and 50-80% during storage.
3 、贮存期间，产品须成卷放置，不得折迭，放置期间应每季翻动 一次。
3. During storage, the products should be placed in rolls and not folded. During storage, the products should be flipped once a quarter.
4 、不同类型、规格层数的输送带不宜接在一起使用，其接头最好采用胶接法。
4. Conveyor belts of different types and layers of specifications are not suitable to be joined together. It is better to use gluing method for their joints.
5 、输送胶带的类型、结构、规格、层数应根据使用条件合理选用。
5. The type, structure, specifications and layers of conveying belt should be selected reasonably according to the use conditions.
6 、输送胶带运行速度一般不宜大于 2 ． 5 米/秒，块度大，磨损性大的物料和使用固定梨的 卸料装置应尽量采用低速。
6. Conveyor Belt should not run faster than 2.5 m/s. Materials with large fragmentation and abrasion and unloading device of fixed pear should be used as low as possible.
7 、运输机的传动滚筒直径与输送带布层的关系、传动滚筒、改向滚筒的配套以及对 托辊槽角 的要求应根据运输机的设计规定，合理选取。
7. The relationship between the diameter of the driving drum and the layers of the conveyor belt, the matching of the driving drum and the reversing drum, and the requirement of the groove angle of the idler should be reasonably selected according to the design regulations of the conveyor.
